Yahoo Answers

Stock radio amp hook up, how to add an amplifier to a factory stereo

You say you also have the harness that goes with your vehicle the one that plugs into the factory radio harness. Behind the factory radio, you can access all of the speaker wires in one place. The speaker wires coming from the amplifier's outputs hook up to your vehicle's harness connected to the car speakers. Hook it to a fuse connected to ignition turn on, like your accessory power fuse. This article and illustration describe how to hook speakers up to an amp that has speaker-level inputs.

How to Connect an Amplifier to a Factory Stereo

However they don't sound any much louder than when my stock was amplified before the bass starts to sound muddy and distorted. This option will obviously render the stock wiring redundant. Secondly, what can i do to add a small amp to stock head unit. You can do that at each speaker's location or at the radio harness.

Any issues with just taping them off other than the usual warnings of tape potentially falling off or just capping them? The amp and speakers would function with the key on-vehicle running, while the orig speakers would serve as the quieter camping speakers when parked with less power drain on my aux battery. Yeah but if you don't splice it with the wires from the receiver to then the fade wouldn't work or balance either on the receiver. Again, using a voltmeter to set gain at Hz won't be accurate. Logan, I'm not familiar with that iSimple kit, but if it makes your iPad's audio output available for an aftermarket amplifier, that's good.

Stock radio amp hook up

Hi, My rear speakers are currently a couple kickers that are connected to an amp. Should I run them in parallel or series or can I just run the wiring from the subs directly to the amp? Ok so I'm trying to connect my iPad to my car speakers and sub.

To submit your questions or ideas, or to simply learn more about It Still Works, contact us. The other ends of these wires connect to the vehicle's harness. Very helpful article, thank you. You will disconnect the factory speaker wires at the speakers, whether unplugging them or by cutting the wires. Hi, I recently put a new stereo head into my Hona Civic Cx, soldering the head unit wires into the original system wires and leaving it at that.

They actually pay me to ramble on, rant, and explain the things I love about music, electronics, dating and getting good sound. We're working to improve the illustration and messaging to make it all easier to understand. When would you prefer that we call you back?

If you installed a powered sub, you will not need to connect the amplifier and speaker, as they are already connected. How do I feed my speaker through the door with the door wire harness in the way? Hi, top 5 best Excellent article firstly! Your amp could be installed near the speaker in the trunk or under a seat. Is there such thing as an adapter I can adapt to the adapter that goes into the factory amp and use for my new amp?

Can I hook up a amp and sub to a stock bose radio

How to Wire an Amp to a Sub and Head Unit 12 Steps

How to hook up subs and amp to stock stereo in car

If you bought your amplifier at Crutchfield, you could call Tech Support for free help troubleshooting your system. For information about other aspects of amplifier installation, like power and ground wiring, check out our Amplifier Installation Guide. Place the amp where you want it, then attach the ground black or brown wire to the amp. It will just plug into your truck and then connect color coordinated wires. Then I discovered all the H.

How to Add an Amplifier to a Factory Stereo

For Tech Support, call Begin chat. And under no circumstances should you connect the output of a receiver to the output of an amplifier - that will damage something. Hi Buck, Let me explain my application and if you could, tell me if how I would be using this is correct in my set up if you could. Connect your amplifier or powered sub to your car's stock head unit. Shop for Car Speaker Installation Parts.

Connecting Your Car Speakers to an Amp Use Your Factory Wiring
How to hook up subs and amp to stock stereo in car

It seems using the wires that are already there would save me a lot of labor. But without knowing precisely what speakers, amp, and subs you're referring to, we can't really help you with advice. Make sure that you use cables with the correct resistance or impedance for your setup. Jordan, Hopefully you meant to say you'll run the speaker wires from the harness to the amplifier's speaker outputs, not inputs - but it sounds like you're on the right track. Lot of redundant questions being asked.

Can I hook up a amp and sub to a stock bose radio

If the amp doesn't seem to be working properly, disconnect your battery again and go back and double-check all of your wiring for possible damaged wire, grounded wire or loose connections. Trying to push watts through factory wiring may result in some power loss but shouldn't introduce distortion. The remote wire tells the amp to turn on. Kevin, If you're just adding a subwoofer to a factory system you can tap the rear speaker wiring for inputs.

Will the high level inputs be affected by the factory amp? Carefully splice into the positive and negative wire on both the right and left rear speakers using a wire stripper. This converter can then be connected directly to your amplifier's line level inputs. Their toll-free number would on your invoice.

Sometimes, the music cuts out when I turn on the car. If you bought any of your gear at Crutchfield, you could call Tech Support for free help troubleshooting your system. Not knowing what receiver you have makes it difficult to address your concern about patch cables. Run the red power wire from your amp installation kit from the positive terminal on your battery through your car's cabin to the location of the amp.

Buck Pomerantz

It Still Works

In the videos I had seen, there were two or sometimes three pairs. David, I'm not sure what you're intending, but the eight conductors should never be connected together. If anyone could please give me an honest answer I would greatly appreciate it.

That way, once the cables are in place, you'll know which of those cables is for the amp inputs and which is for the amp outputs. If you purchase your new speakers from Crutchfield, we'll include our vehicle-specific instructions free with the order, lowe premium matchmaking that illustrate in detail how to do the installation yourself. The only way you can tell if your amps can be strapped together and how to wire them is by referring to their instruction manual. Ok I have a quick question that I seem to find an answer to.

  • The receiver powers the rear speakers only.
  • Source - factory unit connected to scosche hi low converter.
  • Your ears are more accurate.

Tell us about your vehicle. Can the same wires I'm using for the inputs on the alpine amp be used for the subwoofer also? Maybe the store you got your receiver can troubleshoot and repair your setup. Jose, When running multiple amplifiers, you should use a distribution block to safely distribute power to all the amps in your system.

Video of the Day
  1. Therefore the wiring at stock can be left alone and out of the way.
  2. Run the power wire to your amp.
  3. If you're going to replace the factory amp with an aftermarket amp, then you can probably use the factory speaker wires connected to your new amp's outputs.

How to Wire an Amp & Subwoofers Into a Stock Stereo

But amplifiers of watts or less aren't really affected by this, so running their outputs through factory wiring remains a practical and convenient solution. Only a humming sound from each channel. Chris, In order to connect your Epicenter to a factory stereo will probably require a line output converter. Any help will be greatly appreciated, Jay. Wayne, When replacing speakers and wiring, after disconnecting the factory wiring from the speaker, young singles speed dating you can leave it installed as it was.

If you bought a kit it comes with an inline fuse, if you didn't, you need to get an inline fuse. Check out our tech support page for details. My question is how many channels would I need on the processor as well as the amp? When connecting a line out connector to a factory head unit, it is advisable to use both sets of speaker wires to maintain the left and right stereo effect from modern music.

Yahoo Answers

Just match the positive and negatives. Is there no other way to do get this to work without replacing the head unit? The instructions in the receiver's owner's manual will show how it's supposed to get connected. The speaker wires from the new stereo aren't used.

Ive been finding mixed responses on the web. Their toll-free number is on your invoice. And, you could call Tech Support for free help troubleshooting your system. Now attach a line of speaker wire to each splice and secure with electrical tape.

  • Best method for dating tree rings
  • Dating app olympic village
  • Speed dating ni
  • Local dating websites
  • How radiocarbon dating is done
  • Chinese speed dating in manchester
  • Athletic dating app
  • Are there any free dating sites yahoo
  • Hot springs hook up
  • Dating service meet singles matchmaking